Friday, April 24, 2020

From ClarenceH: Painting All These F-ing Tartans

Captain George H. Rippington III
Here's the full list of paints I used for the Queen's Own Cameron Highlanders and bit of advice on the process. It's for my own benefit as well as everyone else's, so when I inevitably leave off for something else - hopefully not any time soon, but remember the AWI project - and return years later to add to the collection, I'll have some clue as to what I did!

All of the paints are from Games Workshop's Citadel range. A brief note on my shorthand. 'Base Coat' is exactly what it sounds like... a solid layer of color painted as neatly as I can. When this is the same as the 'Primer' color (Zhadri Dust in this case), the area was simply left as is which greatly speeds up the painting process. 'Shade' always utilizes the Citadel range of washes or 'shades' which is painted completely over the base coat. 'Layer' is a color painted on that almost completely covers the color below, leaving the darker tones in recesses. This paint is thinned with a tiny amount of water to add a bit of transparency for a softer transition. If there are two 'Layers' in a sequence, the second is painted only on the upper surfaces (the top of arms, the edge of sleeves, collars, and tunics, etc), again thinned with a tiny amount of water. 'Highlight' refers to edge highlighting where only sharp edges or pinpoint highlights are applied. Don't worry about some variation in tones between models - uniforms would be far less... err... uniform after a few months in the Sudan!

Primer
Zhandri Dust Spray Paint

Helmet, Jacket, and Gaiters
Base Coat: Zhandri Dust
Shade: Agrax Earthshade
Layer: Tallern Sand
Layer: Ushabti Bone
Highlight: Screaming Skull (Helmet Only)

Puggaree
Base Coat: Zhandri Dust
Shade: Agrax Earthshade
Layer: Ushabti Bone
Shade: Reikland Fleshade

Valise Kit, Tassels, and Rifle Sling
Base Coat: Administratum Grey
Shade: Agrax Earthshade
Layer: Pallid Wych Flesh

Sporran, Mess Tin Cover, Scabbard, and Boots
Base Coat: Corvus Black
Shade: Agrax Earthshade
Highlight: Dawnstone

Stockings and Sergeants' Stripes
Base Coat: Mephiston Red
Shade: Agrax Earthshade
Layer: Evil Sunz Scarlet
Stripes: Corvus Black

Musket Stock
Base Coat: Rhinox Hide
Shade: Agrax Earthshade
Highlight: Doombull Brown

Canteen Cover and Pistol Holster
Base Coat: Mournfang Brown
Shade: Agrax Earthshade
Layer: Mournfang Brown
Highlight: Deathclaw Brown

Canteen, Bayonet, Sword Blade, and Rifle Barrel
Base Coat: Iron Warrior
Shade: Agrax Earthshade
Highlight: Stormhost Silver (Bayonet Only)

Buttons, Buckles, Sword Hilt, and Rifle Butt Plate
Bace Coat: Liberator Gold
Shade Agrax Eartshade
Highlight: Liberator Gold

Ok... let's pause here for a moment. If you've read this far (what about the bloody tartan? I'm getting to it...) you've probably seen that ALL of these areas are shaded with Agrax Earthshade. To save yourself a huge amount of time, paint all of the base coats on these areas and then shade the entire model before moving on to anything else. After you've finished all of your layers and highlights, you can go back with Agrax Earthshade if necessary and fix any areas where belts may have strayed into one another, to bring out buttons, etc. This will give you a nice, dark edge around the flesh areas too...

Skin
Base Coat: Bugman's Glow
Shade: Reikland Fleshade
Layer: Cadian Fleshtone
Highlight: Kislev Flesh

Kilt
Ok, here we go.. first of all there is no shading or highlighting required. The pattern is busy and the fact that we've left off this stage won't be noticed and would be an even bigger mess than it already is. Having said this, painting the tartan isn't as difficult as it seems.

First, the diagram...


Don't worry about trying to work out how this falls into folds and such. I start by painting the bottom green stripe above the bottom edge and a parallel one midway between the first and the figure's belt. then paint the vertical stripes as evenly as possible all the way around.


No... Citadel hasn't started making paint in dropper bottles. I made these myself. I'll write a post on it at some point if anyone is interested in the how and why.

Base Coat: Kantor Blue
First Stripes: Waagh Flesh
Intersect Squares: Warboss Green (you can stop here for the Black Watch tartan!)
Red Stripes: Flesh Tearers Red
Yellow Stripes: Averland Sunset

The 'Intersect Squares' will likely end up more as dots than squares, but that's ok. The last two colors should be painted with the finest-tip brush you have. Flesh Tearers Red is a Citadel Contrast paint, which means it is somewhat translucent. This is perfect to mimic the stitching of the real thing. It's also thinner than 'normal' paint, which makes it perfect for painting fine lines. There should be TWO parallel red stripes for each one above, but at 28mm, they are lucky to get one. The yellow stripes seem to fall between every other red, so in the case of my models, there is only one about midway up. There would be vertical yellow stripes in the same manner, but I've chose to pretend they are all hidden in the creases! Since there isn't any shading, you can touch up errant strokes with Kantor Blue or Waagh Flesh as necessary, but you only need to correct egregious mistakes.

Stage by stage photos to better illustrate... looks a bit naff viewed at such size and I shudder to publish such pictures, but no sacrifice on my part is too great for you! The illusion works at normal scale - especially when they are seen from three feet away on the game table.






NOTE: The above figure was painted before I settled on my final khaki recipe so appears a little lighter than the finished versions (see the good captain at the start of the post). I wanted the jacket to be a shade darker to better contrast with the white belts and straps.

Finally, here are recipes for alternate colors you might see on British troops in the Sudan:

Alternate Red Coat
Base Coat: Mephiston Red
Shade: Agrax Earthshade
Layer: Mephiston Red
Highlight: Evil Sunz Scarlet

Alternate Grey Coat
Base Coat: Mechanicus Standard Grey
Shade: Agrax Earthshade
Layer: Mechanicus Standard Grey
Highlight: Dawnstone

Alternate Valise Kit (Bread Bag should still be 'white')
Base Coat: Zhandri Dust
Sade: Agrax Earthshade
Layer: Talleran Sand
Highlight: Ushabti Bone

I would only use the alternate valise kit color with the red or grey coat. Rifle units may still have black valise kits at this time and I would use the same formula as for the mess kit and boots above.

Right! Clear as mud? Hopefully this is useful to someone - at least it will help me later! If you have questions, please don't hesitate to ask.

More soon...

13 comments:

  1. Interesting khaki uniform guide and tartan step by step, your a better man than I am Gunga Din!
    Best Iain

    ReplyDelete
  2. Nice work and tutorial Clarence! Thanks for sharing.

    ReplyDelete
  3. Great tutorial and some great looking figures 👍

    ReplyDelete
  4. Great work on these laddies Clarence! Your recipes are way too complex for me. I give myself a base coat of Rioja and aim for something that might reasonably be mistaken as tartan from a distance.

    ReplyDelete
    Replies
    1. LOL.. my pattern isn’t always as neat as this. From three feet away you can’t even see the damn thing.

      Delete
  5. Amazing work; and I would love to see your thoughts and process on putting Citadel paints in dropper bottles.

    ReplyDelete
    Replies
    1. Sure thing, doc.. I’ll document the process the next time I add to the collection. One of the keys to doing this and maintaining sanity is to not try to do them all at one time. Just pull what you need for your current project and transfer those.

      Delete
  6. Really nice work on the tartan and khaki. Thanks for sharing your painting secrets.

    ReplyDelete
  7. Very nice work indeed. Psinting proper tartan on tiny figures surely has to be a little bit crazy, but you’ve pulled it off nonetheless!

    ReplyDelete
  8. This is a truly helpfull and brilliant post thanks for writing all this out for us!

    ReplyDelete
  9. It looks magnificent, but I really hope the day never comes when I have to do tartan...

    ReplyDelete
  10. Stunning work Clarence. I'll do my regiment when the recipe comes in a spraycan. :)

    ReplyDelete